When grid power drops, an NVR and its PoE cameras shut off immediately unless they are backed by an uninterruptible power supply (UPS). To keep recording during an outage, plug the NVR, the PoE switch feeding the cameras, and any connecting network gear into the same UPS, sum the load in watts (typically 15–25 W for an NVR with hard drives and 5–9 W per fixed PoE camera), and estimate runtime by dividing usable battery watt-hours by load watts and multiplying by roughly 0.7 for conversion losses. A small office UPS buys minutes to tens of minutes and protects against surges, while overnight or multi-hour blackouts require a generator or a much larger battery system.
Why the NVR, PoE Switch, and Network Gear Belong on the Same UPS
A wired PoE camera system relies on a single power chain: AC power feeds the NVR and PoE switch, and the PoE switch sends DC power over Ethernet cables to each camera. For a full breakdown of how cameras draw power over Ethernet versus local adapters, see our security camera power supply guide.
When utility power fails without battery backup, the whole system stops at once. However, a common mistake in small-business installs happens when an installer puts the NVR on a UPS but leaves an external PoE switch plugged into a wall outlet or surge-only strip.
If your cameras plug directly into built-in PoE ports on the NVR, putting the NVR on a UPS powers both the recorder and the cameras. Many systems, though, use a standalone PoE switch to feed the cameras and pass video back to the NVR over the local network. If that PoE switch is not on the UPS:
- The NVR stays on: Its hard drives keep spinning and the recorder stays active.
- The cameras die immediately: Without PoE power from the switch, the cameras shut off and the NVR records blank channels or video-loss events.
- Network links drop: If an unbacked network switch sits between the PoE switch and the NVR, the video stream breaks even if the endpoints stay powered.
To keep recording through an outage, the NVR, the PoE switch feeding the cameras, and the network gear connecting them belong on the same UPS (or on dedicated UPS units if located in separate closets). Beyond outage runtime, a UPS also protects the NVR, hard drives, and switch power supplies against damaging voltage sags and surges.
Step 1: Add Up Your Load in Watts
Before picking a UPS, add up the power draw of every device that needs backup power. Guessing the wattage leads either to an overloaded UPS that shuts down immediately or to a battery that drains far sooner than expected.
Typical Wattage Ranges
Small-business PoE camera systems generally fall into predictable wattage ranges:
- NVR with hard drives: Typically 15–25 W. The mainboard draws relatively little power, while each installed hard drive adds a few watts during continuous recording. (If you are still planning how many drives and terabytes your recorder needs, check our NVR storage sizing page.)
- Fixed PoE cameras: Typically 5–9 W each. Daytime draw sits near the lower end, while nighttime operation pushes draw toward 9 W. Because a power outage usually kills building lights at the same time, cameras immediately turn on their infrared (IR) or white-light LEDs, so always budget near the top of the 5–9 W range.
- PTZ cameras: Pan-Tilt-Zoom cameras draw more power than fixed cameras because they run pan/tilt motors, optical zoom lenses, and higher-output illuminators.
- PoE switch and router overhead: A standalone PoE switch uses a small baseline wattage for its own internal circuitry in addition to the PoE load it passes to the cameras, and a router or modem adds a small extra load if included.
Step 2: Choose the UPS Watt Rating and Estimate Runtime
Sizing a UPS comes down to two checks: watt rating (can the UPS output handle your total load?) and battery capacity (how long will the battery keep that load running?).
Watt Rating and Headroom
UPS models are often advertised in volt-amperes (VA) alongside a maximum watt rating. Always compare your calculated load in watts against the UPS's watt rating, and choose a UPS whose watt capacity exceeds your total load with comfortable headroom so the inverter is never running at its absolute limit.
The Runtime Estimation Method
After confirming the watt rating has sufficient headroom, estimate runtime from the battery's capacity in watt-hours (Wh). If the battery specification is listed in volts (V) and amp-hours (Ah), multiply volts by amp-hours to get watt-hours, then apply the runtime formula:
Estimated Runtime (hours) ≈ Usable Watt-Hours (Wh) / Load (W) × 0.7
Multiplying by roughly 0.7 accounts for DC-to-AC conversion losses in the inverter. Multiply the resulting hours by 60 to get minutes.
Worked Estimation Example: A 90 W System Load
Note: This calculation is an estimation method using typical operating loads to help plan capacity, not a product claim or guaranteed specification for any specific model.
Suppose a small business runs an NVR, eight fixed PoE cameras, and a PoE switch with a combined load of about 90 W:
- 1 × NVR with hard drives: ~20 W
- 8 × Fixed PoE cameras (night mode / IR active at ~7.5 W each): 60 W
- PoE switch baseline overhead: ~10 W
- Total estimated load: 90 W
If you connect this 90 W load to an office UPS containing two 12 V, 9 Ah batteries (216 Wh battery capacity):
- Divide watt-hours by load watts and multiply by ~0.7: (216Wh ÷ 90W) × 0.7 = 1.68hours
- Convert to minutes: 1.68 × 60 ≈ 100minutes of estimated runtime.
If you connect that same 90 W load to a compact entry-level UPS with a single 12 V, 7 Ah battery (84 Wh capacity), the same formula ((84Wh ÷ 90W) × 0.7 ≈ 0.65hours) gives about 39 minutes of estimated runtime.
Honest Limits: Minutes vs. Overnight Outages
Setting realistic expectations prevents surprises during a storm: a small office UPS buys minutes to tens of minutes (or around an hour and a half on a dual-battery unit with a ~90 W load), not a whole night of operation.
That window handles everyday power disturbances:
- Brief power flickers (seconds): Prevents the NVR and cameras from rebooting and losing several minutes of footage while restarting.
- Short outages (10–45 minutes): Keeps cameras recording continuously through brief utility trips.
If a site needs continuous recording through multi-hour or overnight blackouts, a small office UPS alone is not enough. Long outages require a generator or a much larger dedicated battery system.
Practical Setup Extras: Remote Viewing, Shutdown Settings, and Testing
Once the UPS is sized, three installation details ensure the setup works when needed. QuarkView is the PoE security camera systems brand of Shenzhen Kuake Trading Co., Ltd., and we recommend checking these points on every installation (all QuarkView hardware carries a 12-month warranty, and surge and battery protection helps protect drives and power boards over time).
1. Place the Router and Modem on the UPS for Remote Viewing
If remote viewing during an outage matters, plug your router and modem into the UPS alongside the NVR and PoE switch. Keep in mind that internet service itself may also be down during a wider blackout—if the ISP's lines lose power, remote viewing will drop until internet service recovers, even though your NVR and cameras keep recording locally.
2. Configure Graceful Shutdown and Auto-Restart Settings
Abrupt power cuts during disk writes can wear hard drives or corrupt recent video files. Where supported, configure graceful shutdown settings so the recorder stops writing cleanly before the battery is exhausted, and verify that both the UPS and NVR automatically power back on and resume recording when utility power returns.
3. Test the Setup by Pulling the Plug Once
Do not wait for a real blackout to find out the PoE switch was plugged into a "Surge Only" outlet on the UPS instead of a "Battery Backup" outlet. After installation, pull the UPS power plug from the wall once while watching the NVR monitor to confirm that the NVR and every PoE camera stay online and recording.
Frequently Asked Questions (FAQ)
What happens if the NVR is on a UPS, but the PoE switch is not?
If an external PoE switch powers your cameras and is not on the UPS, the cameras die immediately when the power goes out, even while the NVR stays up. The NVR, PoE switch, and network gear all belong on the same UPS.
How many watts do an NVR and PoE cameras typically draw?
An NVR with hard drives typically uses 15–25 W, and fixed PoE cameras typically draw 5–9 W each (climbing toward the upper end when night-vision IR LEDs turn on). PTZ cameras draw more power due to their motors and larger illuminators.
How do I estimate UPS runtime for my camera system?
Sum your load in watts, divide usable battery watt-hours by load watts, and multiply by roughly 0.7 for conversion losses. For example, a 216 Wh battery backing a 90 W load gives roughly 1.68 hours (~100 minutes) of estimated runtime.
Can a small office UPS run my cameras all night, and will remote viewing work?
No—a small office UPS buys minutes to tens of minutes, whereas long or overnight outages require a generator or a much larger battery system. Remote viewing during an outage works only if your router and modem are also on the UPS and your internet service provider's lines stay up.
Further Reading for Planning Your System
To compare PoE switches, injectors, and power adapters across different cable runs, read our security camera power supply guide. If you are also selecting hard drives—which affect both your retention timeline and NVR watt draw—visit our NVR storage sizing page to estimate the storage needed for your setup.